Post by mralgae on Oct 29, 2007 10:20:28 GMT -5
Items needed: (pictures will be in the next post)
1. gas cylinder (fire extinguisher)
2. c02 regulator gauge (preferably with needle valve)
3. needle valve (if not with gauge)
4. solinoid
5. c02 tubing
6. check valve (anti flow valve)
7. diffuser
Gas cylinders:
Fire extinguishers are one of the best options as they have the correct fitting for the most used and available gauges on the market. Pub c02 cylinders can be used but adapter units have to be used to convert male thread to female thread for the gauge.
Gauge/regulator:
There are many different types and designs on the market with different designs and reliability, ranging from very cheap to very expensive. From just the basic gauge with pressure only to twin gauge with needle valve to fine tune the amount of c02 released from the bottle. The latter, gauge with needle valve is by far the best option to go for.
If a gauge on its own is bought then a needle valve MUST be bought separately.
Needle valve:
The needle valve allows for very fine adjustment of the c02 coming out of the cylinder.
solinoid
the solinoid turns the unit on & off via electicity. plug this into a timer so it turns on 2hrs before lights on and off 2hrs before lights out.
C02 tubing:
Standard c02 tubing is adequate to use. There is a lot of disagreement on tubing as to how much c02 can leak THROUGH the wall of the tubing.
Check valve:
A check valve imo MUST be used. When the c02 is turned off at night (or god forbid a power cut) the flow and gravity will draw water up the tubing from the tank and then run into the mechanism of the gauge and cause serious damage.
Diffuser:
An ordinary air stone can be used but not recommended for c02 use as the bubbles will be bigger from the stone than from the diffuser, which will give out tiny minute bubbles which will disperse more easily into the water, as the whole idea of c02 is to get as much into the water as possible.
Diffuser Placement:
The placement of the diffuser is important, again so as much c02 gets dissolved into the water. You will get better c02 saturation if the diffuser is placed under the flow of water being pumped back into the tank so the c02 bubbles get swirled/churned up.
Some people but not all, place the end of the tube in to the up take pipe so the c02 gets directed into the filter, were it gets churned up even more than any were else in the tank. The only problem with this is that many say that it makes the filter noisy and causes damage to the filter. I have not used this method so can’t give any real answers only to say I can see both sides of the argument.
1. gas cylinder (fire extinguisher)
2. c02 regulator gauge (preferably with needle valve)
3. needle valve (if not with gauge)
4. solinoid
5. c02 tubing
6. check valve (anti flow valve)
7. diffuser
Gas cylinders:
Fire extinguishers are one of the best options as they have the correct fitting for the most used and available gauges on the market. Pub c02 cylinders can be used but adapter units have to be used to convert male thread to female thread for the gauge.
Gauge/regulator:
There are many different types and designs on the market with different designs and reliability, ranging from very cheap to very expensive. From just the basic gauge with pressure only to twin gauge with needle valve to fine tune the amount of c02 released from the bottle. The latter, gauge with needle valve is by far the best option to go for.
If a gauge on its own is bought then a needle valve MUST be bought separately.
Needle valve:
The needle valve allows for very fine adjustment of the c02 coming out of the cylinder.
solinoid
the solinoid turns the unit on & off via electicity. plug this into a timer so it turns on 2hrs before lights on and off 2hrs before lights out.
C02 tubing:
Standard c02 tubing is adequate to use. There is a lot of disagreement on tubing as to how much c02 can leak THROUGH the wall of the tubing.
Check valve:
A check valve imo MUST be used. When the c02 is turned off at night (or god forbid a power cut) the flow and gravity will draw water up the tubing from the tank and then run into the mechanism of the gauge and cause serious damage.
Diffuser:
An ordinary air stone can be used but not recommended for c02 use as the bubbles will be bigger from the stone than from the diffuser, which will give out tiny minute bubbles which will disperse more easily into the water, as the whole idea of c02 is to get as much into the water as possible.
Diffuser Placement:
The placement of the diffuser is important, again so as much c02 gets dissolved into the water. You will get better c02 saturation if the diffuser is placed under the flow of water being pumped back into the tank so the c02 bubbles get swirled/churned up.
Some people but not all, place the end of the tube in to the up take pipe so the c02 gets directed into the filter, were it gets churned up even more than any were else in the tank. The only problem with this is that many say that it makes the filter noisy and causes damage to the filter. I have not used this method so can’t give any real answers only to say I can see both sides of the argument.
